Bounce errors / 550 5.7.1 Gmail, Microsoft and others
Why was your email rejected with error 550 5.7.1, and who can fix it?
550 5.7.1 means the receiving server refused your message because of a rule: its policy, your reputation or a block list. The words after the code tell you which one, and that decides whether you or the recipient's admin has to act.
- Hard bounce
- Who fixes it: You or their admin
- Try again: No
550-5.7.1 [203.0.113.10] Our system has detected that this message is 550-5.7.1 likely unsolicited mail. To reduce the amount of spam sent to Gmail, 550-5.7.1 this message has been blocked. Please visit 550 5.7.1 https://support.google.com/mail/?p=UnsolicitedMessageError for more information. - gsmtp
You see this at Gmail, Outlook.com, Microsoft 365 and most other providers, each with its own wording after the code.
Here is how to read that message.
Each colour marks one part of the message, and the numbers match the notes underneath.
- 1The reply code550 is a permanent rejection. Sending the same message again gives the same answer.
- 2The status code5.7.1 means delivery not authorized, message refused. RFC 3463 says it can result from per-host or per-recipient filtering.
- 3The words that matterThis is the only part that tells you the cause. Match it against the versions above before you do anything else.
- 4The servergsmtp is Google's tag. Other providers end their messages differently.
Here are other versions of this message you may see.
The words after the code are what separate one cause from another. Find yours.
Outlook.com and Hotmail, when the sending network is on a block list
550 5.7.1 Unfortunately, messages from [203.0.113.10] weren't sent. Please contact your Internet service provider since part of their network is on our block list (S3140).
Microsoft 365, when the sending IP is blocked
5.7.1 Service unavailable; Client host [203.0.113.10] blocked using Blocklist 1; To request removal from this list please forward this message to delist@microsoft.com
Microsoft 365, when you may not send to that recipient or group
Remote Server returned '550 5.7.1 RESOLVER.RST.AuthRequired; authentication required'
Google Workspace, when the recipient's admin set a rule
550 5.7.1 This message violates example.com email policy. - gcdp <sessionid> - gsmtp
Here is what the message means in plain words.
RFC 3463 defines 5.7.1 as delivery not authorized, message refused: the sender is not authorized to send to the destination. In practice it is the catch-all for no, because of a rule.
The rule might be the provider's judgement that your mail looks unsolicited, a block list your sending IP is on, or a setting the recipient's company chose, such as a group that only accepts mail from its own members. A gcdp tag in a Google message means a custom rule set by a Workspace admin.
These are the usual reasons for it.
- The provider's filters think the message is unsolicited, or the sending IP or domain has a very low reputation.
- Your sending IP, or the network it sits in, is on a block list.
- SPF, DKIM or DMARC are missing or failing.
- The recipient is a group or mailbox set to accept mail only from certain senders.
- The recipient's admin created a rule that blocks your address or domain.
Who has to fix it?
The blue card is the one that fixes it. A dashed card helps in some cases, and a grey card has nothing to do.
550 5.7.1You, the sender
Fixes itYou fix it when the words mention spam, reputation or a block list.
The person you emailed
SometimesThey can ask their admin to allow you, when the words mention a policy or a group.
Their email admin
Fixes itTheir admin fixes it when the words mention policy, a group or access, because only they can change the rule.
Follow these steps to fix it.
- Read the words right after 5.7.1.Match them against the four versions shown above. They decide which of the next steps applies.
- If it mentions spam, reputation or a block list, check the block lists.The email blacklist checker shows whether your domain or sending IP is listed. A message that names a removal address, such as Microsoft's delist address, tells you where to ask.
- Check authentication.Missing SPF, DKIM or DMARC records are a common reason a provider turns suspicious. The domain health check shows all three.
- Lower your volume and spread it out.A new mailbox that sends a lot on day one looks like exactly what spam filters exist to stop. Warm it up gradually and keep your daily volume steady.
- Clean your list.Dead addresses and spam traps read as a sign you did not get permission for the list. Verify the list and remove the bounces.
- If it mentions a policy or a group, contact the recipient another way.Microsoft's guidance is that you usually cannot fix this yourself. Ask the person to tell their email admin, who can add you to the allowed senders or change the rule.
Here is how to stop it from happening again.
Providers judge three things in a set order: whether the message is authenticated, whether the sender has a good reputation, and whether the list is made of real addresses.
Reputation
Steady volume, few complaints and a mailbox warmed up before a campaign.
Open the email warmup →These errors look similar, and here is how they differ.
| Error | Where you see it | What it means | Try again? |
|---|---|---|---|
| 550 5.7.1 | Gmail, Microsoft and others | This page. Rejected for policy, reputation or a block list | No |
| 550 5.7.26 | Gmail | SPF and DKIM did not pass. The sender is unauthenticated. | No |
| 421 4.7.0 | Gmail | Temporary. Gmail is rate limiting your mail. | Yes, automatically |
| 550 5.7.509 | Microsoft 365 | The sending domain fails DMARC and its policy is reject. | No |
| 554 5.7.1 | AOL | The recipient only accepts mail from specific addresses. | No |
These are the questions people ask about this error.
Does 550 5.7.1 always mean I am blacklisted?
No. A block list is one of several causes. A policy rule, a missing authentication record or a low reputation can produce the same code. The words after it tell you which.
Is 550 5.7.1 permanent?
Yes, the 5 at the start means permanent for that message. Fix the cause and send a new message afterwards.
What does gcdp mean in a Google error?
Google adds gcdp when the error comes from a custom rule set by a Workspace admin. Only the admin of the recipient's domain can change it.
Who do I contact?
If the words name a block list, follow the removal steps in the message. If they name a policy or a group, reach the person another way and ask them to tell their email admin.
Can I resend straight away?
Not until you have found the cause. The same message from the same sender returns the same answer.
Other bounce errors you may run into.
These are the sources behind this page.
The message wording and the fixes come from the providers' own documentation and from the RFC that defines the codes.
Send from a mailbox that providers trust.
Emailchaser warms up your mailboxes and sends your cold emails at a steady pace from your own domain.